1What is straight mineral oil?
It is the lubricating oil as obtained by fractional distillation of crude oil. It does not have any additives.
2What is ashless dispersant (AD) oil?
A mineral lubricating oil containing additives that disperse the contaminants throughout the oil so they will not clump and clog oil passages. There are no ash-forming additives in AD oil.
3What is synthetic oil?
A lubricating oil that is made by chemicaclly changing the nature of an oil base to give it the needed characteristic. Synthetic oil is the primary oil for turbin engines.
4Is automotive oil suitable for use in aircraft engines?
No, automotive oil and aviation oils are formulated for entirely different operating conditions.
5What is meant by multi-viscocity oil?
It is a lubricating oil with a viscocity index improver that increases the viscocity of the oil when it is hot and decreases viscocity when it is cold.
6Where can you find the grade of engine oil specified for a particular aircraft?
In the airplane flight manual or the pilot's operating handbook for the aircraft.
7What are the SIX functions of the oil in an aircraft engine?
1. Reduces friction
2. Seals and cushions
3. Removes heat
4. Cleans inside the engine
5. Protects against corrosion
6. Performs hydraulic action
8What is the purpose of an air-oil seperator, or deaerator, in a turbine engine oil tank?
In normal operation, the oil picks up a quantity of air and it is swirled as it enters the deaerator. The swirling action releases the air from the oil, and air is used to pressurize the oil tank.
9How is oil pressure regulated in an aircraft engine?
A pressure-relief valve senses the desired pressure and sends excess oil back into the engine sump.
10What is the purpose of the restricted orifice in the line between the oil pressure gauge and the engine?
The restricted fitting helps dampen any pulsations in the oil caused by the pump.
11What is a hot-tank lubrication system for a turbojet engine?
A lubrication system in which the oil cooler is in the pressure subsytem and the scavenged oil is not cooled before it is returned to the tank.
12What is a cold-tank lubrication system for a turbojet engine?
A lubrication system in which the oil cooler is in the scavenge subsystem, and the scavenged oil is cooled before it is returned to the tank.
13Where does a wet sump oil system store oil
In a reservoir inside the engine.
14Where does a dry-sump oil system store oil?
In a reservoir outside the engine through the use of a scavenge pump and external tubing.
15What is the purpose of a chip detector?
magnetic chip detectors are ised in the oil system to detect and catch forrous (magnetic) particles present in the oil. During maintenance, the chip detectors are removed from the engine and inspected for metal; if none is found, the detector is cleaned, replaced, and safety wired. If metal is found on a chip detector, an investigation should be made to find the source of the metal.
16What component in a reciprocating engine lubrication system must be inspected on a 100-hour or annual inspection?
The oil sump or tank, the oil strainer screen, the oil filter, the oil cooler and the temperature control valve, the oil pressure and temperature gauges and any tramsmitters associated with them, and the entire engine for indication of oil leaks.
17What two instruments show the condition of a reciprocting-engine lubrication system?
Oil pressure and oil temperature gauges.
18What must be done to an oil filter when it is removed from the engine?
It should be cut open and the pleated element examined to determine the type and amount of contaminant carried by the oil.
19What is a spectrometric oil analysis program?
-A program in which a sample of oil is taken from the engine at regular intervals and sent to a lab, where it is burhe resulting light is analyzed for the wavelengths of the elements that are present in the oil sample.
-A single sample is meaningless. There must be a series of samples taken at regular intervals to measure the change in the amount of elements present in the oil.
-Traces of aluminum, copper, and iron in the oil indicate wear of the pistions or wrist pin plugs (aluminum), cylinder walls or piston rings (iron), or main bearing or bushing (copper).
20What type of oil quantity indicator is used in most aircraft engines?
A dipstick that measures the quantity of oil in the tank or sump.
21When should the engine oil quantity be checked on a turbine engine?
As soon as practical after the engine is shut down.
22Where is the oil temperature measured on a reciprocating engine?
Usually at the oil pressure screen before the oil goes into the engine passages.
23Why do engine manufacturers recommend that engine lubricating oil be changed at specific intervals?
The oil picks up contaminants and carries them throughout the engine where they can cause wear. The oil also becomes acidic and causes corrosion in the engine.
24What problem can improper piston ring conditioning (also known as run-inor break-in) lead to?
High oil consumption
25What are the causes of high oil comsumption in a reciprocating engine?
-Failing or failed bearing
-Worn or brokem piston rings
-Incorrect installation of piston rings
-External oil leakage
-Leakage through engine fuel pump vent
-Engine breather or vacuum pump breather
26What is the danger of mixing engine oils?
Oils may not be compatible with each other and can cause the degrading of the oil properties leading to unsatisfactory lubrication of the engine. When adding oil to an engine, add the same type of oil that was used previously.
27What are the risks of using engine lubricants other than those specified by the manufacturer?
The engine was tested and certified with specific lubricants that allowed the engine manufacturer to meet the regulations for the engine design. The use of lubricants that were not certified may lead to dangerous wear and lubrication issues in the engine, leading to premature failure. Follow the manufacturer's recommendations when using engine lubricants.
28What cautions should be used when handling, storing, and disposing of used lubricating oils?
Used oils are a hazardous material that is damaging to the environment. Proper handling , storage, disposal, and recycling methods must be followed carefully.
29What is meant by the viscocity of engine lubricating oil?
The resistance of the oil to flow.
30How is oil temperature controlled on a reciprocating engine?
Hot oil is directed through the core of the oil cooler, but cold oil is directed around the outside of the core so it will not be further cooled.
31Is the temperature shown on the aircraft instrument panel the temperature of the oil entering the engine or of the oil leaving the engine?
It is the temperature of the oil entering the engine.
32What is the purpose of the oil dilution valve in a reciprocating engine?
When very cold weather is anticipated, gasoline can be mixed with the lubricating oil before the engine is shut down. This reduces the viscocity of the oil and makes starting easier. When the engine is running the gasoline evaporates out of the oil.
33What is the function of the hopper in the oil tanks used with some reciprocating engines?
Hoppers are a part of the oil dilution system. Only the oil in the hopper is diluted. This speeds up delution and requires less gasoline.
34What happens to the gasoline that is used to dilute the oil in the crankcase of an aircraft reciprocating engine?
When the engine is runnign the oil is warm, the gasoline evaporates out of it.
35What is the purpose of the sludge plugs in the crankshaft of a reciprocating engine?
They trap sludge that is in the oil and hold it until the engine is disassembled at overhaul.
36Which pump is larger in a dry-sump lubricating system, the pressure pump or the scavenge pump?
The scavenger pump has the greater volume
37Why do full-flow oil filters have a spring-operated bypass valve in them?
In case the filter should plug up so it cannot pass any oil, the bypasss valve will open and allow unfiltered oil to flow through the system.
38What is the function of the fuel / oil heat exchanger in the lubrication system of a turbojet engine?
This allows heat from the oil to warm the fuel so ice will not form.
39What kind of oil is used on most turbojet engines?
Synthetic oil.
40Where are the last chance oil filters located in a turbojet engine?
They are located inside the engine, just ahead of the nozzles that spray oil onto the bearings.
41What information must be displayed around the oil filler opening for a turbojet engine?
The word "Oil" and the permissible oil designations, or references to the AFM for permmissible oil designations.
42What is the function of the oil control rings on the piston of an aircraft reciprocating engine?
They maintain the proper quantity of oil between the piston and the cylinder wall.
43What indication woudl the pilot have if the oil quantity was low?
The oil temperature would be high and the oil pressure would be low.