Reciprocating Engines

34 flashcardspar Coldtour
Réviser ces flashcardsGratuit · répétition espacée · iPhone, Android, Mac et web

Toutes les cartes

1
What are the basic types of configurations for reciprocating engines?
Radial, Opposed, Inline, V-type
2
In what position should the crankshaft be when a magneto is being times to an engine?
The piston in cylinder No. 1 should be in the correct position for ignition to occur. This is normally ≈ 30° before top center on the compression stroke.
3
What is checked on engine run-up to determine the operational condition of the engine?
-Oil Pressure
-Idle RPM and Mixture
-Fuel Pressure and Flow
-Manifold Pressure
-Engine Acceleration
-Maximum Static RPM
-Magneto Drop
-Ignition switch safety check
-Propeller pitch change and/or feathering
4
What is a Hydraulic Lock in an aircraft engine?
Oil has drained past the piston rings and filled the combustion chamber of cylinders that are below the centre line of the engine. If the crankshaft is turned over with this oil in the cylinder it will lock, and there is a probability that the pistion, cylinder, or connecting rod will be damaged.
5
What are the strokes of a Four-Stroke reciprocating engine?
Intake, Compression, Power, Exhaust.
6
What are the two main causes of a cylinder having low compression?
Piston rings not seating / broken OR Valves not seating / burned
7
What is a low-tension ignition system?
It is an ignition system using a magneto with a brush-type distributor and a coil that has NO secondary winding.
-Low voltage is directed from the magneto to a transformer mounted on the cylinder head. At this point the low voltage is stepped up to a higher voltage and is directed through a short high-tension lead, and finally, to the spark plug.
-There is one transformer for each spark plug
8
What are some advantages of a horizonttally opposed engine?
-Low power-to-weight ratio
-Ideal for installation on aircraft wings
-Low vibration characteristics
9
How can you determine the firing order og an 18-cylinder radial engine?
Begin with Cylinder No.1. ADD 11 or SUBTRACT (whichever keeps the number between 1 and 18).

1-12-5-16-9-2-13-6-17-10-3-14-7-18-11-4-15-8
10
How is Hydraulic Lock removed from an aircraft engine?
Remove the sprak plug from the locked cylinder and drain all the oil out. Clean the spark plug and replace it.
11
What is a Floating Cam Ring on a large radial engine?
It is a cam ring that rides on a shelf-type bearing wuth a large amount of clearance between the bearing and the ring. When adjusting the valves on an engine with a floating cam ring, the pressure of the valve springs opposite the valve beign adjusted must be removed so the cam ring will be tight against the bearing of the valves being adjusted.
12
Why is valve clearance adjusted on radial engines but not horizontally opposed engines?
Most horizontally opposed engines have hydraulic valve lifters that keep all of the clearance out of the valve train, while raidal engines have solid lifters.
13
What are both hot and cold valve clearances given for most radial engines?
The hot clearance is given for valve timing purposes. The timing is adjusted with the valves in cylinder No.1 set with hot clearance. When timing is set, all of the valves are adjusted to their cold clearance.
14
Why is it important to preserve engines that will not be operated for an extended period of time?
Moisture will accumulate in the engine, initiating the corrosion process which can ruin the engine.
15
Preservation for temporary storage is valid for engines that will be out of service for how many days?
30 to 90 days
16
What should be done to the cylinders to protect them from rust and corrosion when preparing the engine for long-time storage?
Spray preservative oil inside the cylindersand replace the spark plugs with dessicant plugs.
17
What is the formula for calculating indicated horsepoweron a 4-stroke engine?
Indicated HP = PLANK ÷ 33,000

Where:
-P = Indicated mean effective pressure (psi)
-L = Length of the stroke (ft)
-A = Area of Piston / Cylinder bore (sqr. in)
-N = Number of power strokes per minute (RPM ÷ 2)
- K = Number of Cylinders
18
What is Specific Fuel Consumption?
SFC is a measure of the economical use of fuel, which is the fuel weight in pounder per hour, per horsepower:

SFC = (pounds fuel / Hr) ÷ horsepower
19
What must be inspected to determine the airworthiness of an engine installation?
-The porpeller
-Lubrication system
-Ignition system
-Fuel metering system
-Cooling system
-Exhaust system
20
Where can you find the corect grade of fuel and amount of engine lubricating oil for an aricraft engine?
In the Type Certificate Data Sheet (TCDS) for the aircraft
21
What are the basic steps in troubleshooting an engine installation?
-Know how the system should operate
-Observe how the system is operating
-Divide the system into smaller parts to find trouble
-Look for the obvious problem first
22
Where do you find instructions for removing an engine from an aircraft?
In the aircraft maintenance manual
23
Whaat must be done to a nose-wheel airplane before removing the engine?
The tail of the airplane must be supported.
24
What should be used to cover the endds of fuel and oil lines that have been disconnected from the engine?
The correct plugs or caps. Never use tape to cover the lines.
25
What is meant by a QEC engine assembly?
An engine that has been prepared for a quik engine chnage. The engine is on its mount and all of the accessories are installed. A minimum of time is required to change engines. All that is needed is for the controls, wiring, and fluid lines to be connected to the firewall.
26
What is meant by rigging the engine controls so they have some "cushion"?
The control on the engine component must contact its stops before the control handle in the flight deck reaches its stop. This causes the control handle to spring back a slight amount when it is moved to the extendof its travel
27
What are two ways of pre-oiling an engine?
A. Before the spark plugs are installed and after the oil tank or sump is filled, turn the engine over with the starter until oil runs out of the fitting to which the oil pressure gauge connects.

B. Use a pre-oiler tank. Aire pressure forces oil through all of the passages until some of it flows from the oil pressure gauge fitting.
28
What checks should be made to determine the proper operation of a reciprocting engine installation?
-Idle RPM and Mixture
-Static RPM
-Propeller pitch change
-Magneto check
-Ignition switch safety check
-Carburetor heat check
29
What is the purpose of a cold cylinder check?
A cold cylinder check determines which cylinder is not firing. Run the engine for a few minutes at the speed, and on the magnet, at which it runs roughest. Shut it down and feel the exhaust stack nearthe cylinder head. The cylinder with the stack that is not as hot as the others is the cylinder that has not been firing.
30
How is fuel ignited in a diesel cycle engine?
The diesel cycle engine depends on high compression pressures to provide for the ignition of the air-fuel mixture in the cylinder.
31
What are the risks of moving a propeller by hand during aircraft maintenance?
If the ignition switch is on, or a magneto gorund wire is faulty, the engine can start if the impulse coupling is fired when the propeller is turned. maintenance personel should always verify the magneto seitch id off and stay clear of the propeller arch any time the propeller is moved.
32
What precautions should be taken prior to ground operation of an engine?
Improper procedures during ground operation runs can cause damage to the aricraft and injury to personel. The maintenance manual anad operational checklists should always be used when operating an engine and aircraft on the ground.
33
What are the risks associated with incorrect procedures in the event of a reciprocating engine fire?
Improper procedures can lead to further damage to the aircraft and engine. If the engine backfires and causes a fire in the induction system, the starter motor should continue to run while the mixture is pulleed to idle-cutoff to prevent more fuel from entering the engine. If the fire is outside of the engine, pull the mixture control to idle-cutoff and close the fuel firewall shutoff valve to stop the flow of fuel into the engine compartment. After aircraft maintenance, it is good practice to have a spotter standing by with a fire extinguisher.
34
What are the risks associated with using procedures other than those developed by the manufacturer?
The risk of usingother procedures is that important steps and procedures can be missed, causing damage to the engien, aircraft, or personel. The manufacturer's procedures were carefully developed to maintain the type design configuration and safety of the aircraft.
Réviser les 34 cartes gratuitement

Plus de flashcards

Hemoglobin 33 cartesSciences · AnglaisCHRISTYAllergens (SPA-ENG)27 cartesLangues · Espagnol → AnglaisBrentCh 6 Vocab22 cartesMathématiques · Anglaisjocyt9Genki 1 (2nd ed.) Chap. 1 Greetings18 cartesLangues · Japonais → Anglaisセクシー熊Eugene O’Neill14 cartesHistoire et lettres · Anglaisdourelinorcensorship10 cartesAnglaisanya€English Vocabulary: Meanings of Smart166 cartesLangues · AnglaisNaiwwwc'est fou chez nous121 cartesFrançaisanneAviation Meteorology 285 cartesAnglaisAdrianTaxes64 cartesÉconomie et gestion · AnglaisTaraPhilippine Criminal Law: Jurisdiction and Extradition50 cartesDroit et politique · AnglaisSANGALLAMATH 341 Midterm 141 cartesMathématiques · AnglaisJane

Révise ces decks dans l’app

Gratuit sur iPhone, Android, Mac et le web. Ajoute n’importe quel deck à ton compte en un tap.

Télécharger dans l’App StoreDisponible sur Google Play
Réviser les 34 cartes gratuitement